WindyNation's P30L solar charge controller is a premium grade PWM solar controller. The digital display provides all necessary solar system information and also serves as a user interface for adjusting the charge controller's settings. It is the perfect solar charge controller for an RV, boat, small cabin or any other off-grid installation, where user configurability and system information is important.
WindyNation P30L PWM 30 Amp solar charge controller prevents battery from being overcharged and damaged by the solar panel. Ideal for 12 and 24 volt batteries. Controller can be configured for AGM, lead acid, gel and other battery types.
Advanced electronic protection: overload, short circuit, and reverse polarity protected
LCD digital display provides system information (amperage, voltage, temperature, load control etc.)
Battery temperature sensor (BTS) is included. See photo gallery.
System settings are user adjustable by using the MODE and UP and DOWN buttons
Product Information Specifications for P30L LCD 30A PWM Solar Panel Regulator Charge Controller with Digital Display and User Adjustable Settings Below:
Solar charge controllers are high quality, efficient and reliable solar power regulators.
Suitable for all 12/24v DC lamps. They are perfect for rural electrification
They offer a lot of possibilities and benefits.
Can be used to control lighting devices.
Regulations point: 14.4 Volts;
Low voltage disconnect: 11.1V Volts;
Low voltage reconnect: 12.6 Volts;
Microcontroller digital accuracy;
Type of Charging: Series PWM & stat of charge(SOC);
4 Stages: equalization, PWM, Boost and Float, temperature compensated charging;
Electronic protections: Short circuit and over current-solar and load;
Reverse polarity-solar, load, battery;
Reverse current at night;
Limits high voltage to protect loads; Lighting protection;
Conformal coated printed circuit board;
Features: Intelligent control is realized by using microprocessor and dedicated control calculationÂ¡Â£ Five load working modes: pure lighting control, lighting control & timing control, hand operation and debug mode. Using large-diameter wire terminal, can fix the wire which max size is 6mm Parameter is set to power-down save function, the system model and control parameters, and other important data are stored inside the chip, after power is not lost, to make the adjustment more convenient, more reliable system. Using 2 digital LEDs display and settings, one-button operation to complete all of the settings, intuitive and easy to use. Specifications: Rated charge current: 30A Rated load current: 30A Work voltage: 12V/24V AUTO No load losses current: 5mA-20mA (only when digital LEDs being lighted) Charging circuit voltage drop: â‰¤0.26V Load circuit voltage drop: â‰¤0.15V Over voltage protection: 14.8V; x2/24V Boost charge voltage: 14.6V; x2/24V Direct charge voltage: 14.4V; x2/24V Float charge voltage: 13.6V; x2/24V Charge recover voltage: 13.2V; x2/24V Over discharge recover voltage: 12.6V; x2/24V Lower voltage indication: 12.0V; x2/24V Over discharge voltage: 11.1V; x2/24V (no load) real-time modified voltage by the discharge rate Temperature compensation: -4.0 MV/â„ƒ 2V (boost voltage direct charge, float charge and charge return voltage compensation) Control method: PWM pulse-duration modulation charge mode Working temperature: industry stage: -35â„ƒ~+55â„ƒ Color: black Note: Let the little children away from the storage battery and the controller Package Includes: 1*Digital PWM 30A Solar Charge Controller 1*User Manual
The Renogy Wanderer is a 30A PWM charge controller. This advanced negative-ground controller is designed for off-grid solar applications and can be used with a 12V battery or battery bank. Integrating highly efficient PWM charging, the Wanderer increases battery life and improves system performance. The controller comes equipped with fully comprehensive self-diagnostics and electronic protection functions to prevent damage from installation mistakes or system faults. Negative grounding controller ensures the broader off grid applications and safety, especially to be used on a vehicle which has battery negative on the chassis. A little extra investment on the right charge controller will generate a much higher return and prevent system failure.
MPPT TRACER 3215RN Solar Charge Controller 30A 12V 24V EP
Why we recommend buy MPPT Solar Controller? MPPT circuit solar controllers are considerably more elaborate than PWM. The voltage of the solar panel changes with time of day and temperature. The optimum voltage for battery charging changes as the state of charge of the battery. The MPPT charge controller matches these voltages and can result in 30% more efficient transfer of power. This means good MPPT solar charge controllers can reduce the number of solar panels needed by up to 30%- a tremendous benefit. Even if the excess panels are purchased, benefits are realized in a Grid Tie system because more electricity can be sold back to the grid. While only a small part of system price, a MPPT solar panel charge controller can leverage the rest of the system to better performance. Specification: * Model No: Tracer-3215RN * Nominal System Voltage: 12VDC | 24VDC Auto work * Rated Battery Current: 30A * Maximum Battery Voltage: 32V * Max. Solar Input Voltage: 150VDC * Max. PV input power: 12V/ 390W 24V /780W * Self-consumption:
Instapark INCC1205 12V / 5A Waterproof PWM Solar Charge Controller
Color: One Color
The Instapark INCC1205 solar charge controller is designed and engineered to prevent your 12V battery from overcharging when it's connected to a solar panel, therefore protect your investment and extend the battery life. The INCC1205 solar charge controllers is equipped with PWM technology to ensure that your battery reaches its maximum charging capacity without causing any damage to the battery. Similar to other modern high quality battery chargers, PWM algorithm gradually reduces the charging current to avoid over-heating of the battery, yet the charging continues to return the maximum amount of energy to the battery in the shortest time resulting in higher charging efficiency, faster recharging and a healthier battery at its full capacity. Each INCC1205 charge controller comes with four green LED indicators and one red LED indicator displaying battery status, connection status and real-time battery charge capacity. The INCC1205 solar charge controller is in full conformance with both CE and RoHS standards and is backed up by a standard 2-year manufacturer's warranty. Specifications: Rated solar input current: 5A Rated output charging current: 5A Charging voltage: 12.8V Cut-off voltage: 14.6V Float voltage: 13.8V Temp Comp. (mV/Â°C): -30mV/-60mV Temperature: -31Â°F to 131Â°F Package Includes: Instapark INCC1205 12 volt / 5 amp Solar Charge Controller Battery Terminal Clamps 5.5mm x 2.1mm female to bare wires (solar panel output) adapter User manual
Why we recommend buy MPPT Solar Controller? MPPT circuit solar controllers are considerably more elaborate than PWM. The voltage of the solar panel changes with time of day and temperature. The optimum voltage for battery charging changes as the state of charge of the battery. The MPPT charge controller matches these voltages and can result in 30% more efficient transfer of power. This means good MPPT solar charge controllers can reduce the number of solar panels needed by up to 30%- a tremendous benefit. Even if the excess panels are purchased, benefits are realized in a Grid Tie system because more electricity can be sold back to the grid. While only a small part of system price, a MPPT solar panel charge controller can leverage the rest of the system to better performance. Specification: * Model No: Tracer-1210RN * Nominal System Voltage: 12VDC | 24VDC Auto work * Rated Battery Current: 10A * Maximum Battery Voltage: 32V * Max. Solar Input Voltage: 100VDC * Max. PV input power: 12V/ 130W 24V /260W * Self-consumption:
Preset CO2 control at 1500 PPM. Built-in 'self calibration' feature. Easiest to use CO2 Controller on the market. ETL listed for use in commercial applications. Simply plug in your CO2 generator or regulator and you are ready to go. Built-in photocell allows CO2 enrichment only during daylight hours. Durable powder-coated steel housing. 15 Amps/120 Volts/60 Hz. 3 year warranty.
Manufacturer: Morning Star
Brand: Morning Star
A high quality, reliable and economically priced charge controller from Morningstar. Features their advanced PWM pulse charging algorithm.
Other features include selectable battery type and temperature compensation.
Model #: SS-10-12V
LVD (low voltage disconnect): No
Vdc (voltage direct current): 12V
Solar Amps: 10 A
Load Amps: 10 A
Weight: 1 lb. / .45 kg
Dimensions: 5.9" x 2.1" x 1.3" / 149.86 x 53.4 x 33.02 mm
Warranty info: 5 year warranty from manufacturer